Machine Vision
246 topics in this forum
-
- 0 replies
- 215 views
SCDI and DOAL are the same. Red, Blue, & IR = 50Reflect / 50 Transmit White = 30Reflect / 30 Transmit
Last reply by Omron Forums Support, -
- 0 replies
- 196 views
The attached file gives some ideas on the differences between NL-200 Series and LC-50/LC-100. kA23800000008EyCAI_en_US_1.pdf
Last reply by Omron Forums Support, -
- 0 replies
- 203 views
* check to see if it is a strobe unit. If it is, you will need to use a strobe controlled. * Be sure to use a current controller to prevent damage to the light. The pinout of this light can vary. The current pin-out should be power on pin 1, and ground on pin 3. The pin-out can also be power on pin 1, and ground on pin 2. The wire colors of the black cable with a green over-mold on the 4-pin M12 connector is: 1 = Brown 2 = White 3 = Blue 4 = Black
Last reply by Omron Forums Support, -
- 0 replies
- 241 views
The OCV Fontless tool will group touching characters as a single character to be inspected. However if a OCVRuntime or a OCVFont tool is used, a library must be created for each character inspected. This allows the OCVRuntime or OCVFont tool to be able to train a code that has touching characters. Please remember to increase the "Allowed Overlap During Read" found in the LayoutStep datum (tab). For most applications I set this to 5 pixels.
Last reply by Omron Forums Support, -
- 0 replies
- 233 views
During the installation if the CRC error relating to the readme file is displayed. The user can click Ignore and allow the installation to continue. The installation will complete and the I-PAK software will run properly The I-PAK VH error message is shown below Operating System Any
Last reply by Omron Forums Support, -
- 0 replies
- 221 views
A sample 1 camera equipment list has been created for the I-Pak HE and I-Pak SE configurations I-Pak HE sample equipment list https://na3.salesforce.com/00P500000055XpR I-Pak SE sample equipment list https://na3.salesforce.com/00P500000055XpX
Last reply by Omron Forums Support, -
- 0 replies
- 260 views
21 CFR Part 11 Administrator — Administrator mode allows the defining of valid users, their passwords and their security levels. This Administrator, whose user name is I-PakAdmin and default password is 999999, is your Configuration Manager. This user is not a Programmer, a Supervisor nor an Operator.
Last reply by Omron Forums Support, -
- 0 replies
- 198 views
In order to reset the 21 CFR Part 11 I-Pak Administrator password, use the registry editor (regedit), navigate to HKEY_CURRENT_USER\Software\Visionscape\Visionscape I-Pak\Settings\Startup and modify the value "Admin_paswd". Once you have modified the value, then the login is "I-PakAdmin" and the password will be the value set in the registry. The defualt value is "999999".
Last reply by Omron Forums Support, -
- 0 replies
- 237 views
Some USB to RS-232 adapters have communication problems. The most prominent is the Belkin model.
Last reply by Omron Forums Support, -
- 0 replies
- 184 views
Hanhelds: MS-Q Quadrus Handheld HawkEye 40T and 45T Handheld HS-21 HS-41X HS-2D Mobile Hawk UID Checker Program and verifiers: UID LDP Verifier UID DPM Verifier Quadrus EZ Quadrus Verifier
Last reply by Omron Forums Support, -
- 0 replies
- 145 views
VisionHAWK WVGA Spectral Response - Image001.png VisonHAWK SXGA Spectral Response - Image002.png VisionHAWK C-Mount 2 Megapixel Spectral Response - Image005.png
Last reply by Omron Forums Support, -
To clear the error run regedit.exe from command promt and delete the following key: HKEY_CURRENT_USER\Software\Visionscape\FrontRunner\VsRunView
Last reply by Omron Forums Support, -
- 0 replies
- 195 views
The Attached document shows the specifications of the 83-200051-xx Mounting bracket for a Smart Series DOAL and the QX-Hawk or C-Mount VisionHAWK. kA23800000008AJCAY_en_US_1.pdf
Last reply by Omron Forums Support, -
- 0 replies
- 192 views
The scanners and imagers with a 5V interface all use the same trigger input scheme. The input is rated for 0-24VDC, which will make it compatible with most sensors. The Trigger input uses a 5V pull-up to hold the line in the High state. To activate the input, pull the trigger pin to zero volts, or use an NPN trigger signal. Wiring diagrams are provided in the Appendix of all User's Manuals. This is identical for Input 1 and the New Master pin
Last reply by Omron Forums Support, -
- 0 replies
- 289 views
If the VS-1 job is not loading, it may be because the bootloader is telling the VS-1 to not load or run the job. To change the bootloader settings for loading and running the job, type the following at the telnet: "BP_UpdateStartupOptions (1,1)" and the job loaded and ran. To open a Telnet window, connect to the IP address of the VS-1 at port 23 and enter "target" as the login and "password" as the password.
Last reply by Omron Forums Support, -
- 0 replies
- 261 views
Mouse settings related to hover can cause an eventual crash of AutoVision. kA23800000008FGCAY_en_US_1.pdf
Last reply by Omron Forums Support, -
- 0 replies
- 247 views
This procedure will allow you to reset a Microscan handheld scanner (HS-2D (obsolete), HS21, HS-41X, Mobile Hawk) back to factory default settings either for user convenience or in the event the unit becomes unresponsive. Operating System Any kA23800000008KrCAI_en_US_1.pdf
Last reply by Omron Forums Support, -
- 0 replies
- 199 views
The minimum bar width must be a minimum of 2 pixels for the barcode tool. Larger element sizes are needed for robust PDF417 barcode reading. This can be accomplished by using Rect Warp with scale factor set to 150% for X and Y. The Barcode tool ROI must be made significantly larger than the barcode for the algorithm to locate and properly decode the barcode.
Last reply by Omron Forums Support, -
- 0 replies
- 233 views
Incorrect files may result in : 1. An error message in the Visionscape debug window: Failed to Read Image File: The file c:\...tif is either missing or corrupt. 2. A crash of the Visionscape Software itself. The File must be an uncompressed TIFF Image with 8-bit color depth. Files saved from Visionscape software will automatically be in the proper format.
Last reply by Omron Forums Support, -
- 0 replies
- 203 views
A comparison is made between the WVGA and SXGA ID-40 with regards to a minimum required shutter time. The comparison was made with both devices at fixed focus at 50mm and red outer illumination. The shutter time is related to the maximum linear speed that the code can travel during reading. For the Vision / QX Hawk platform the WVGA is faster than the SXGA. On the MicoHAWK platform the SXGA is faster than the WVGA. WVGA SD @ 50mm, 250usec shutter, red outer LED. SXGA SD @ 50, 50usec shutter, red outer LED. Operating System Any
Last reply by Omron Forums Support, -
- 0 replies
- 192 views
To be able to work with the IC3USB the Virtual COM Port number has to be between 1 & 4. On most laptops these ports are being used by other features, or the Auto assignment is always higher. You can go to device manager and change the port number to one the IC3USB can work with.
Last reply by Omron Forums Support, -
- 0 replies
- 224 views
Setting the gateway can only be done with a telnet connection to the camera. The procedure below applies to Visionscape 6.0.3 or higher (AutoVISION 2.0.3 or higher). For reference in the commands below: Camera IP = 192.168.0.10 Subnet Mask = 255.255.255.0 Gateway = 192.168.0.100 Procedure Open a Command Prompt in Windows and enter the following command telnet 192.168.0.10 You should see in the window -> Enter the following command (case sensitive). This is the IP Address, the Subnet Mask, and the Gateway. BP_UpdateIP(“192.168.0.10”,”255.255.255.0”,”192.168.0.100”) You should get the response value = 0 = 0x0 Enter the following command (case sensitive) BP_Dump…
Last reply by Omron Forums Support, -
- 0 replies
- 182 views
Will give direct setup details on how to use Telnet Window to Receive Vision Hawk Results. kA238000000086fCAA_en_US_1.pdf
Last reply by Omron Forums Support, -
- 0 replies
- 347 views
If you have forgotten the password, type in the password 228489. A numeric string will be generated and provided to you. Call Microscan support, and supply the reported string. You will be provided with a temporary password that is good for one use. You will need to change your password after access is granted.
Last reply by Omron Forums Support, -
- 0 replies
- 231 views
See attachment. Operating System Any kA238000000CgFkCAK_en_US_1.docx
Last reply by Omron Forums Support,
-
Upcoming Events
No upcoming events found -
Most Contributions
-
-
Topics
-
-
Popular Contributors
-
1
-
2
-
