Jump to content
OMRON Forums

Matsuzawa Makoto

Members
 View Profile  See their activity

  • Posts

    31

  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Matsuzawa Makoto's Achievements

Contributor

Contributor (5/14)

  • First Post
  • Collaborator Rare
  • Week One Done
  • One Month Later
  • One Year In

Recent Badges

0

Reputation

  1. Matsuzawa Makoto
    AX1111 cannot output pulse and direction?
  2. Matsuzawa Makoto
    I want to link two linear units to one unit using Yaskawa's FT77. (Yaskawa call it thrust assist mode.) In that case, can I tune from PMAC? Connecting is analog torque.
  3. Matsuzawa Makoto
    I want to know how to connect for pulse and direction. There is exist only how to connect analog to driver on OMRON site. How to do the connecting on CK3W-AX1414?
  4. Matsuzawa Makoto
    Hello everyone. Can BissC use 1/T extension same as Quadrature Encoder? Thank you for your answer,regards.
  5. Matsuzawa Makoto
    Hello everyone. I want to get ACC-14E manual whera can I get? I can't find manuals from after the site was changed Deltatau to OMRON thanks!
  6. Matsuzawa Makoto
    I really thanks. Your anser correct me becouse I was thinking Quadrature is differential.
  7. Matsuzawa Makoto
    I used TTL means single
  8. Matsuzawa Makoto
    Hello everyone. I want to use hand pulse transmitter with ACC-24E2S. Teach me wich ACC-24E2S's encorder port is differential or TTL? regard
  9. Matsuzawa Makoto
    Can I ok do the firmware update without permission by OMRON?
  10. Matsuzawa Makoto
    Thank you answer me. I know Power PMAC supports CS Pos, CS Vel, CS Torq so that I thought it don't have to bother writing same as other servo drive.
  11. Matsuzawa Makoto
    #4 Elmo DC Drive (CS Pos, CS Vel, CS Torq Modes) ↑ I want to know why only Elmo DC Drive especialy write three control methods
  12. Matsuzawa Makoto
    Hello I want to connect R88D-KT02H. I tryed to connect as follows but I can't read Encoder and I can't move. Please teach me how to connect correctly. R88D-KT02H------------------ ACC-24E3 TREF1/VLM [14]--------------[ 1] DAC1A+ AGND [15]--------------[ 8] AGND RUN [29]--------------[ 4] AE_NO1 ALM_COM [36]--------------[11] AE_COM1 +24VIN [ 7]---------------[12] FAULT+ /ALM [37]--------------[ 5] FAULT- +A [21]--------------[14] CHA+ -A [22]--------------[ 6] CHA- +B [49]--------------[13] CHB+ -B [48]--------------[ 5] CHB- +Z [23]--------------[12] CHC+ -Z [24]--------------[ 4] CHC- POWER SUPPLY------------- ACC-24E3 GNC --------------------------[11] AE_COM +24V --------------------------[12] FAULT+
  13. Matsuzawa Makoto
    I want to install IDE3 later, not IDE4 later. I'll try.thank you
  14. Matsuzawa Makoto
    There is IDE4 installed pc. Can I instal IDE 3 to that PC after without trouble? I"m afraid IDE4 environment will break.
  15. Matsuzawa Makoto
    I read PMAC IDE4 manual. Matlab Coder Simulink Coder Embedded Coder ↑ conversioning to c language is prepared on the pmac side, are they needless?
×
×
  • Create New...